The difference between MB and Mbps shows up when you download a file. MB and GB measure an amount of data, such as a file size or the data left on your plan. Mbps and Gbps measure how much data can move each second. A plan advertised at 100 Mbps and a download app showing 12.5 MB/s can be describing the same speed.
How to read MB and Mbps
An uppercase B stands for byte, while a lowercase b stands for bit. The ps in Mbps and Gbps means per second, and the slash in MB/s does the same job. A 100 MB file contains 100 megabytes. At 100 MB/s, your connection transfers that much data every second.
| Unit | Meaning | Example |
|---|---|---|
| MB | Megabyte | A photo that takes up 5 MB |
| GB | Gigabyte | A 10 GB data allowance equals 10,000 MB |
| Mbps | Megabits per second | A 100 Mbps connection is equivalent to 12.5 MB/s |
| Gbps | Gigabits per second | A 1 Gbps connection is equivalent to 1,000 Mbps |
The table uses decimal units, so 1 GB equals 1,000 MB. Apps that use binary units may show GiB and MiB instead. The NIST reference for binary prefixes defines 1 GiB (gibibyte) as 1,024 MiB (mebibytes). The same file can have a different number depending on the unit. For example, a file containing 1,000,000,000 bytes is 1 GB or about 954 MiB.
How to estimate download time from MB and Mbps
Start with the file size in MB and the download speed in MB/s. One byte contains eight bits, so divide the speed in Mbps by 8 to get MB/s. If your download app shows MB/s and you want to compare it with a speed test in Mbps, multiply the app’s number by 8.
At 100 Mbps, dividing by eight gives you 12.5 MB/s. A 1 GB file contains 1,000 MB, so 1,000 ÷ 12.5 gives you 80 seconds. The table compares speeds from 25 Mbps to 1 Gbps. Each estimate assumes the connection holds that speed until the file finishes downloading.
| Download speed | Equivalent rate | Time to download 1 GB |
|---|---|---|
| 25 Mbps | 3.125 MB/s | 5 minutes 20 seconds |
| 100 Mbps | 12.5 MB/s | 1 minute 20 seconds |
| 300 Mbps | 37.5 MB/s | About 27 seconds |
| 1 Gbps | 125 MB/s | 8 seconds |
The same calculation works for uploads. If your connection gives you 100 Mbps down and 20 Mbps up, use the 20 Mbps figure to estimate how long it takes to send a file. At that rate, uploading 1 GB takes about 6 minutes and 40 seconds under ideal conditions. When you livestream, the number of simultaneous streams affects how much upload speed you need. See the Wordtura review of Restream for an example.
Why your download app can show a lower speed
Say your speed test shows 100 Mbps and your download app shows 10 MB/s. Multiply the app’s figure by eight and you get 80 Mbps, which is 20 Mbps below the speed test result. At that average rate of 10 MB/s, a 1 GB file takes about 100 seconds.
A speed test measures your connection to the server it uses. A download from a different server can be slower. A weak Wi-Fi signal or other devices using the same network can also affect the speed you get. To see whether Wi-Fi is a factor, run the test again on the same device over Ethernet if you can. The AT&T guide to internet speeds covers the factors that affect speeds on individual devices.
How a 1 GB data allowance differs from a 1 Gbps connection
A 1 GB data allowance tells you how much data you can use. A connection advertised at 1 Gbps can transfer 1,000 megabits per second at its rated speed, which works out to a theoretical 125 MB/s. When comparing plans, check the GB figure for the data allowance and the Mbps or Gbps figure for speed.
Downloading a 500 MB file uses about half of a 1 GB allowance whether your connection runs at 100 Mbps or 1 Gbps. The file size tells you roughly how much of your allowance you’ll use, and the speed determines how long you’ll wait. Your provider may record slightly more data than the file size because the transfer also carries protocol information.
